Audi 80/90/Coupe

since 1986-1991 release

Repair and operation of the car



Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12:10. Back door (Coupet's model)
   12:11. Forward door, lower door loop
   12:12. Adjustment of a window and the bearing door element
   12:13. The window condensing traffic jams, the window regulator
   12:14. Door lock
   12:15. Draft of lever transfer of the lock
   12:16. Rope of the internal door lock
   12:17. Rotary clamp, adjusting spring
   12:18. Adjustment of doors
   12:19. The bearing door element
   12:20. Central lock
   12:21. The pump with two modes of forcing
   12:22. Leading activator
   12:23. Activator of a back door
   12:24. Trunk lid activator
   12:25. Activator of a cover of the fuel tank
   12:26. Door glass (Coupet's model)
   12:27. Adjustment of a butt slip (Coupet's model)
   12:28. Framework of a back door, lower loop of a door
   12:29. The bearing element of a back door, the condensing stopper
   12:30. Rope, hinged lever
   12:31. Door handle
   12:32. Holder of components of a door
   12:33. Hatch
   12:34. Bumper casing
   12:35. Sealing of a rear bumper
   12:36. The extending clamp
   12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
   12:38. Top overlay of a forward spoiler (Coupet's model)
   12:39. Back spoiler / laying of a niche of a wheel
   12:40. Rear bumper (Coupet's model)
   12:41. Window regulators
   12:42. Internal finishing of a body
   12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment


12.7. Cowl

Removal

PERFORMANCE ORDER
1) remove a windshield washer jet hose

2) uncover a loop 1, unscrew bolts 2

Installation

Carry out installation upside-down.

Adjustment

PERFORMANCE ORDER
1) screw up bolts 2
2) to make an inhaling only manually
3) carefully push a cowl to a windshield until it does not rise aflush with wings
4) tighten bolts 2; 21 N. of m.
5) weaken bolts 3
6) adjust cowl height so that it coincided with wings
7) tighten bolts 3; 15 N. of m.

Adjustment of a gap between a cowl and a wing

PERFORMANCE ORDER
1) weaken wing bolts
2) shift a wing that the gap made value and

and = 4.5 + 1.0 mm


Trunk lid, hinge, rack (Sedan models)


1. Trunk lid limiter
2. The hinged limiter, in the closed position
3. Insulating washer
4. Combinational bolt, 21 N. of m.
5. The fixing clip
6. Gas-filled rack
7. Six-sided nut, 21 N. of m.