Audi 80/90/Coupe

since 1986-1991 release

Repair and operation of the car

Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12:10. Back door (Coupet's model)
   12:11. Forward door, lower door loop
   12:12. Adjustment of a window and the bearing door element
   12:13. The window condensing traffic jams, the window regulator
   12:14. Door lock
   12:15. Draft of lever transfer of the lock
   12:16. Rope of the internal door lock
   12:17. Rotary clamp, adjusting spring
   12:18. Adjustment of doors
   12:19. The bearing door element
   12:20. Central lock
   12:21. The pump with two modes of forcing
   12:22. Leading activator
   12:23. Activator of a back door
   12:24. Trunk lid activator
   12:25. Activator of a cover of the fuel tank
   12:26. Door glass (Coupet's model)
   12:27. Adjustment of a butt slip (Coupet's model)
   12:28. Framework of a back door, lower loop of a door
   12:29. The bearing element of a back door, the condensing stopper
   12:30. Rope, hinged lever
   12:31. Door handle
   12:32. Holder of components of a door
   12:33. Hatch
   12:34. Bumper casing
   12:35. Sealing of a rear bumper
   12:36. The extending clamp
   12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
   12:38. Top overlay of a forward spoiler (Coupet's model)
   12:39. Back spoiler / laying of a niche of a wheel
   12:40. Rear bumper (Coupet's model)
   12:41. Window regulators
   12:42. Internal finishing of a body
   12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment

12:19. The bearing door element

GENERAL INFORMATION

The bearing door element, the sizes

in the drawing the cross section of the left door is shown

the sealing edge 7 has to have contact on all contour of a rack and a decorative overlay of a roof 3

with = 3.5 + 1 mm

d = 8.1 + 1 mm

1 – sealing flange
2 – door frame
3 – decorative overlay of a door
4 – window
5 – window sealing laying

6 – internal door sealing laying
7 – sealing edge
8 – a sealing edge at a window

Adjustment

Prevention

The first windows and a covering of a door have to be adjusted.

Two experts will be necessary for implementation of this operation. Do not press a door covering during adjustment.

PERFORMANCE ORDER

	1) weaken bolts (shooters)
2) close a door
3) slightly press on the bearing element in the direction opposite to a roof and a rack; apply slightly more than forces, than it is necessary; rubber laying will return the bearing element to proper position
4) at this time the second expert (from within the car) tightens at first the top, and then lower bolts

The bearing element of a back door, removal / installation

Removal

PERFORMANCE ORDER

1) remove the decorative panel of a door

2) disconnect a rope of the internal uncoupling door mechanism

3) disconnect and remove a rope from the bearing door element

4) remove a fixing pin 1, having pressed forward on a door lock covering

5) unscrew bolts with a six-sided head 2, 3

Installation

Carry out installation upside-down, in view of the following:

tighten bolts with a six-sided head with m 20 N.' moment.

A-and – a cross-section

In = a zone between a roof and a back rack of a body

1 – adjustable limiter of the regulator of a window

adjust the top limiter of the regulator of a window so that the upper edge of a window 3 adjoined to the condensing flange 2 in a transitional zone B

and = 0 + 0.5 mm