Audi 80/90/Coupe

since 1986-1991 release

Repair and operation of the car



Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12:10. Back door (Coupet's model)
   12:11. Forward door, lower door loop
   12:12. Adjustment of a window and the bearing door element
   12:13. The window condensing traffic jams, the window regulator
   12:14. Door lock
   12:15. Draft of lever transfer of the lock
   12:16. Rope of the internal door lock
   12:17. Rotary clamp, adjusting spring
   12:18. Adjustment of doors
   12:19. The bearing door element
   12:20. Central lock
   12:21. The pump with two modes of forcing
   12:22. Leading activator
   12:23. Activator of a back door
   12:24. Trunk lid activator
   12:25. Activator of a cover of the fuel tank
   12:26. Door glass (Coupet's model)
   12:27. Adjustment of a butt slip (Coupet's model)
   12:28. Framework of a back door, lower loop of a door
   12:29. The bearing element of a back door, the condensing stopper
   12:30. Rope, hinged lever
   12:31. Door handle
   12:32. Holder of components of a door
   12:33. Hatch
   12:34. Bumper casing
   12:35. Sealing of a rear bumper
   12:36. The extending clamp
   12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
   12:38. Top overlay of a forward spoiler (Coupet's model)
   12:39. Back spoiler / laying of a niche of a wheel
   12:40. Rear bumper (Coupet's model)
   12:41. Window regulators
   12:42. Internal finishing of a body
   12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment






12:26. Door glass (Coupet's model)

Removal

PERFORMANCE ORDER
1) completely lift a windowpane
2) note the provision of glass in relation to a frame and the holder, as shown in the drawing (insert)

1 – central rack of a body, top

2 – the central rack of a body, situation on the holder

3 – a forward rack of a body, situation on the holder

3) half lower a window
4) weaken bolts on the holder
5) remove aluminum clamping slips with sealants
6) remove glass

Installation

Prevention

On cars with identification number to 8BKA 008300 the black plastic substrate has to be replaced with a white plastic substrate.


PERFORMANCE ORDER
1) place a plastic substrate in a standard position
2) place glass in a standard position and combine it with marks in a frame and the holder; if original glass is lost or broken, at first place glass between carving openings
3) carefully insert glass in the holder, forward and back
4) establish a plastic substrate
5) establish aluminum clamping slips
6) manually screw up bolts
7) arrange the back holder (from the central rack of a body) parallel to a guide
8) by means of a wrench pull (shooter) down until the spring on a rope contracts completely
9) completely tighten bolts