Audi 80/90/Coupe

since 1986-1991 release

Repair and operation of the car



Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12:10. Back door (Coupet's model)
   12:11. Forward door, lower door loop
   12:12. Adjustment of a window and the bearing door element
   12:13. The window condensing traffic jams, the window regulator
   12:14. Door lock
   12:15. Draft of lever transfer of the lock
   12:16. Rope of the internal door lock
   12:17. Rotary clamp, adjusting spring
   12:18. Adjustment of doors
   12:19. The bearing door element
   12:20. Central lock
   12:21. The pump with two modes of forcing
   12:22. Leading activator
   12:23. Activator of a back door
   12:24. Trunk lid activator
   12:25. Activator of a cover of the fuel tank
   12:26. Door glass (Coupet's model)
   12:27. Adjustment of a butt slip (Coupet's model)
   12:28. Framework of a back door, lower loop of a door
   12:29. The bearing element of a back door, the condensing stopper
   12:30. Rope, hinged lever
   12:31. Door handle
   12:32. Holder of components of a door
   12:33. Hatch
   12:34. Bumper casing
   12:35. Sealing of a rear bumper
   12:36. The extending clamp
   12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
   12:38. Top overlay of a forward spoiler (Coupet's model)
   12:39. Back spoiler / laying of a niche of a wheel
   12:40. Rear bumper (Coupet's model)
   12:41. Window regulators
   12:42. Internal finishing of a body
   12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment






12.5. Forward wing

GENERAL INFORMATION

Forward wing, assembly (Coupet's model)
1. Nut
2. The self-cutting bolt with a washer, 8 N. of m.
3. The self-cutting bolt with a washer
4. Wing
5. The extending nut
6. Wing arm
7. The self-cutting bolt with a washer, 8 N. of m.
8. Washer
9. The condensing ring
10. The condensing laying

Forward wing, removal

PERFORMANCE ORDER
1) remove a front bumper
2) remove laying of a cavity of a wheel
3) remove the condensing laying (shooter)

Installation

Install all components in the return to removal an order, in view of the following:

PERFORMANCE ORDER
1) establish a rivet of a basic arm of a cowl (arrow A)
2) establish a rivet of a stopper of a door (arrow B)
3) establish strips of a sealing cord, 1, 2 and sheet laying with a bolt And on a stopper

1 = 480 mm in length and 7.0 mm in the diameter

2 = 250 mm in length and 7.0 mm in the diameter

Use a sealing cord of AKD 497 010 04 R10 or an equivalent, and squeeze it to the sizes of 7.0 mm in the diameter.

Adjustment of a forward wing, cowl gap

PERFORMANCE ORDER
1) weaken all bolts of a wing
2) having weakened bolts, adjust a gap, moving a wing
3) having weakened bolts, adjust a gap, moving a wing

and = 4.5 + 1.0 mm

Prevention

Numbers of details are intended only for reference. Always apply for the latest information to your dealer.

The sealing cord will need to be squeezed to diameter in 7.0 mm