Audi 80/90/Coupe

since 1986-1991 release

Repair and operation of the car


Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12:10. Back door (Coupet's model)
   12:11. Forward door, lower door loop
   12:12. Adjustment of a window and the bearing door element
   12:13. The window condensing traffic jams, the window regulator
   12:14. Door lock
   12:15. Draft of lever transfer of the lock
   12:16. Rope of the internal door lock
   12:17. Rotary clamp, adjusting spring
   12:18. Adjustment of doors
   12:19. The bearing door element
   12:20. Central lock
   12:21. The pump with two modes of forcing
   12:22. Leading activator
   12:23. Activator of a back door
   12:24. Trunk lid activator
   12:25. Activator of a cover of the fuel tank
   12:26. Door glass (Coupet's model)
   12:27. Adjustment of a butt slip (Coupet's model)
   12:28. Framework of a back door, lower loop of a door
   12:29. The bearing element of a back door, the condensing stopper
   12:30. Rope, hinged lever
   12:31. Door handle
   12:32. Holder of components of a door
   12:33. Hatch
   12:34. Bumper casing
   12:35. Sealing of a rear bumper
   12:36. The extending clamp
   12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
   12:38. Top overlay of a forward spoiler (Coupet's model)
   12:39. Back spoiler / laying of a niche of a wheel
   12:40. Rear bumper (Coupet's model)
   12:41. Window regulators
   12:42. Internal finishing of a body
   12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment


12.4. Forward guard
GENERAL INFORMATION

Forward guard (Sedan models)
1. A bolt with a six-sided head, 23 N. of m.
2. The self-cutting screw, 7.5 N. of m.
3. Guard, lower section
it is possible to remove together with the central section
4. The self-cutting screw, 7.5 N. of m.
5. A bolt with a six-sided head, 23 N. of m.		 6. The bearing lock plate
it is possible to remove together with the central or lower section
7. Metal ear
at removal of a guard pull it directly down for a corner
8. The self-cutting screw, 7.5 N. of m.
9. Guard, central section

Forward guard in collecting (Coupet's model)
1. A bolt with a six-sided head, 23 N. of m.
2. The self-cutting screw with a washer
3. Guard, central section 		4. Guard, lower section
5. The self-cutting screw with a washer

Removal

PERFORMANCE ORDER
1) remove a bumper
2) remove a front grille
3) unscrew the decorative panel (arrows)
4) pull out a guard from the condensing ring to the right or to the left

Removal for the Sedan model

PERFORMANCE ORDER
1) through an opening for access remove the holder of a rope and disconnect a rope
2) unscrew screws of a casing of stitched air (arrow)
3) to remove a guard, pull it under a wing down

Removal for Coupet's model

PERFORMANCE ORDER
1) remove a bumper
2) remove a front grille
3) disconnect a cowl rope
4) unscrew screws of a decorative covering (arrow) and pull out it from the condensing ring
5) unscrew an air duct of the cooling air and an arm of a radiator (arrow)
6) unscrew an arm of the oil heater
7) disconnect the switch of a lamp of motor office
8) disconnect a connecting loop on the guard panel
9) unscrew the directing device of the soaked-up air (arrow)

Installation

Carry out installation upside-down.