Audi 80/90/Coupe

since 1986-1991 release

Repair and operation of the car



Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12:10. Back door (Coupet's model)
   12:11. Forward door, lower door loop
   12:12. Adjustment of a window and the bearing door element
   12:13. The window condensing traffic jams, the window regulator
   12:14. Door lock
   12:15. Draft of lever transfer of the lock
   12:16. Rope of the internal door lock
   12:17. Rotary clamp, adjusting spring
   12:18. Adjustment of doors
   12:19. The bearing door element
   12:20. Central lock
   12:21. The pump with two modes of forcing
   12:22. Leading activator
   12:23. Activator of a back door
   12:24. Trunk lid activator
   12:25. Activator of a cover of the fuel tank
   12:26. Door glass (Coupet's model)
   12:27. Adjustment of a butt slip (Coupet's model)
   12:28. Framework of a back door, lower loop of a door
   12:29. The bearing element of a back door, the condensing stopper
   12:30. Rope, hinged lever
   12:31. Door handle
   12:32. Holder of components of a door
   12:33. Hatch
   12:34. Bumper casing
   12:35. Sealing of a rear bumper
   12:36. The extending clamp
   12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
   12:38. Top overlay of a forward spoiler (Coupet's model)
   12:39. Back spoiler / laying of a niche of a wheel
   12:40. Rear bumper (Coupet's model)
   12:41. Window regulators
   12:42. Internal finishing of a body
   12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment






12:18. Adjustment of doors

GENERAL INFORMATION

adjust a gap, displacing door loops

and = 5 + 1 mm

b = 5.5 + 1 mm

level height with the line of the case

The place of adjustment – a loop (very big openings on a loop in the place where she joins the forward / central rack of a body).

To avoid noise from air, regulate on assembly loops or in a back part of doors on a pin of a locking plate.

Sections A-and, B-B, C-C:

with = 0.5 + 0.5 mm

Section D-D:

d = 14.5 mm

Door gap, adjustment

PERFORMANCE ORDER
1) having unscrewed bolts 1, unscrew the plug with cutting which is behind bolts until it does not cease to adjoin to a forward rack of a body
2) weaken bolts 2, close a door and adjust a gap, moving a door
and = 5 + 1 mm
3) weaken or tighten by means of a wrench
4) screw up the plug with cutting until she does not contact with a forward rack of a body
5) screw up bolts and clamp them with m 30 N.' moment.
6) check a gap

Adjustment of height
PERFORMANCE ORDER
1) weaken bolts 1 and 2
2) weaken or tighten by means of a wrench
3) move door loops
4) tighten bolts; 30 N. of m.
5) weaken bolts (shooters), and displace a door in the necessary direction

6) tighten bolts; 30 N. of m.

Prevention of noise from wind

1 – the screwed detail of the threaded connection

2 – a washer with bowl-shaped dredging

3 – washer


Two washers with bowl-shaped dredging can be in case of need used.

PERFORMANCE ORDER
1) adjust the screwed detail of the threaded connection of a latch in a back part of a door
2) the screwed detail of the threaded connection of 50 N. of m.

Doors, adjustment (Coupet's model)

PERFORMANCE ORDER
1) adjust a door gap, displacing door loops
2) establish the door height (a body contour). Adjustment is made on loops (very big openings on a loop in the place where the loop fastens to a forward rack of a body)
3) for prevention of emergence of noise from wind regulate assembly loops of a door or in a back part of a door on a locking plate
4) weaken bolts 2, 4 by means of a wrench
5) unscrew the plug with cutting on bolts 2 from a forward rack of a body
6) close a door and displace it for adjustment of a gap
7) twist the plug with cutting 3 until is contact with a forward rack of a body
8) screw up bolts and tighten them with m 30 N.' moment.
9) double-check a gap

Adjustment of height

PERFORMANCE ORDER
1) weaken bolts 2, 4 by means of a wrench
2) unscrew the plug with cutting on bolts 2 from a forward rack of a body
3) close a door
4) displace door loops
5) tighten bolts with m 40 N.' moment.

Noise from wind in a forward part of a door, prevention

PERFORMANCE ORDER
1) weaken bolts 1
2) displace a door as it is required
3) tighten m 30 N.' bolts.

Noise from wind in a locking plate, prevention

PERFORMANCE ORDER
adjust a clamp pin in a back part of a door

pin of a clamp of 16 N. of m.

1 – clamp pin
2 – shock plate
3 – substrate

for achievement of exact adjustment more than one can be established

Door gap, adjustment (Coupet's models since 1990 model years)

PERFORMANCE ORDER
1) having unscrewed bolts 1, unscrew the plug with cutting until it does not cease to adjoin to the central rack of a body
2) weaken bolts 2, close a door and adjust a gap, displacing a door
and = 5 + 1 mm
3) open a door and tighten bolts 2 with m 30 N.' moment.

Prevention

Unscrew or screw up, using a key of 2598.


4) twist plugs with a carving 3 until they do not adjoin to the central rack of a body
5) screw up bolts, 30 N. of m.
6) check a gap

Door height, adjustment

PERFORMANCE ORDER
1) weaken bolts 1 and 2

Prevention

Unscrew or screw up, using a key of 2598.


2) displace door loops in very big openings
3) tighten bolts with m 30 N.' moment.

Noise from wind, elimination

PERFORMANCE ORDER
1) weaken bolts of a forward door (arrow), displace a door in grooves of loops
2) distance between a framework of a door and the central rack of a body
d = 14.5 mm
3) tighten bolts with m 30 N.' moment.

Back door, elimination of noise from wind

1 – shock washer

2 – a washer with bowl-shaped dredging

Two washers with bowl-shaped dredging can be in case of need established.

Adjustment of a pin of a clamp of the lock of a door allows to eliminate noise in a back part of a door.

PERFORMANCE ORDER
1) adjust a clamp pin
2) 50 N. of m.