Audi 80/90/Coupe

since 1986-1991 release

Repair and operation of the car



Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12:10. Back door (Coupet's model)
   12:11. Forward door, lower door loop
   12:12. Adjustment of a window and the bearing door element
   12:13. The window condensing traffic jams, the window regulator
   12:14. Door lock
   12:15. Draft of lever transfer of the lock
   12:16. Rope of the internal door lock
   12:17. Rotary clamp, adjusting spring
   12:18. Adjustment of doors
   12:19. The bearing door element
   12:20. Central lock
   12:21. The pump with two modes of forcing
   12:22. Leading activator
   12:23. Activator of a back door
   12:24. Trunk lid activator
   12:25. Activator of a cover of the fuel tank
   12:26. Door glass (Coupet's model)
   12:27. Adjustment of a butt slip (Coupet's model)
   12:28. Framework of a back door, lower loop of a door
   12:29. The bearing element of a back door, the condensing stopper
   12:30. Rope, hinged lever
   12:31. Door handle
   12:32. Holder of components of a door
   12:33. Hatch
   12:34. Bumper casing
   12:35. Sealing of a rear bumper
   12:36. The extending clamp
   12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
   12:38. Top overlay of a forward spoiler (Coupet's model)
   12:39. Back spoiler / laying of a niche of a wheel
   12:40. Rear bumper (Coupet's model)
   12:41. Window regulators
   12:42. Internal finishing of a body
   12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment


лазерная резка киев фанеры.

12:24. Trunk lid activator

GENERAL INFORMATION

Trunk lid activator


Removal

PERFORMANCE ORDER
1) remove decorative finishing of the right back dimensional lamp; for weakening of a lock ring the leading activator has to be in situation "the door is open"
2) pushing a lock ring down, carefully you hold draft of lever transfer 2
3) extend draft of lever transfer from the activator
4) unscrew assembly bolts and remove a pressure head / vacuum hose

Installation

Carry out installation upside-down, in view of the following:

PERFORMANCE ORDER
1) the pressure head / vacuum hose has to be between draft of lever transfer of the lock and an internal part of the hatch of a luggage carrier
2) to collect draft of lever transfer 2, it is necessary that the lock and the activator were in open situation
3) press draft 2, pushing a lock pin 1 up

Trunk lid activator (Coupet's model)


Removal

PERFORMANCE ORDER
1) remove decorative finishing of the right back dimensional lamp; for weakening of a lock ring draft of lever transfer has to be in situation "the door is open"
2) carefully keeping draft of lever transfer, push a lock ring 2 in the direction specified by an arrow
3) pull out draft from the activator
4) remove a pressure head / vacuum hose and unscrew fixing bolts (shooters)

Installation

Carry out installation upside-down, in view of the following:

PERFORMANCE ORDER
1) the pressure head/vacuum hose has to be between draft, the lock and the decorative panel of a luggage carrier
2) to establish draft of lever transfer 1, the lock and the activator have to be in situation "the door is open"
3) push draft, a lock ring up
4) do not squeeze draft of lever transfer