Audi 80/90/Coupe

since 1986-1991 release

Repair and operation of the car


Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
- 8. Transmission
   8.1.2. A fork - the main cylinder of coupling
   8.1.3. Press clutch plate
   8.1.4. Malfunctions of coupling
   + 8.2. Mechanical transmission 012
   + 8.3. Mechanical transmission 01A
   + 8.4. Automatic transmission 089
   - 8.5. Automatic transmission 087
      8.5.2. Lever and rope of the lever of gear shifting
      8.5.3. Mechanism of management of a butterfly valve
      8.5.4. Removal and installation of the transmission
      8.5.5. Check of the moments of gear shifting
      8.5.6. Main transfer
   8.6. Dismantling and assembly of automatic transmissions
   8.7. Block of valves
   + 8.8. Automatic transmission 097
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
+ 12. Body, salon
+ 13. Air conditioning system
+ 14. Electric equipment


8.5.2. Lever and rope of the lever of gear shifting
GENERAL INFORMATION

Mechanism of the lever of gear shifting and rope of gear shifting

1. 3 N. of m.
2. Cover
3. Electromagnetic switch
4. The torsion spring
5. 5 N. of m.
6. Plug
7. Washer
8. Gear shifting lever switch
check
the engine has to be started when the lever
switchings is in the provision of P or N
headlights of a backing have to light up at inclusion of transfer of a backing
if is not present, turn the switch in a nest and again check its work
9. Basis
at installation put a layer of AKD 512 001 sealant between the basis and a body
10. Clip bolt
11. Boss
12. Washer
13. Coupling
14. Plug
15. Kronsheyn
16. Lock ring
17. Gear shifting lever rope
with a guide and the plug
grease the ends of a rope before installation
tighten a nut of fastening of a rope on an arm
to 15 N. of m.
check that the directing tube densely sat
move the gear shifting lever
in situation P (against the stop back)
tighten a rope clip nut to 20 N. of m.

18. 23 N. of m.
19. Cover
if necessary, replace
check the accuracy of its installation that moisture did not get on a gear shifting rope
20. Coupling
21. Washer
22. 20 N. of m.
23. The switching lever
24. Washer
25. Spring clamp
26. Plug
27. Washer
28. Compression spring
install on the switching lever before installation of the directing pin
29. The directing pin
30. Switching lever предач
with a fork for locking of the lever in the provision of P or N
31. Casing of the lever of an adventure of transfers
is established by designation P forward
establish after a regupirovka of the electromagnetic switch
32. Gear shifting lever handle

Installation of an arm of the lever of gear shifting in relation to the gear shifting lever

PERFORMANCE ORDER
1) install the probe A, 1.0 mm thick, between the lever of gear shifting and the electromagnetic switch
2) move the gear shifting lever in situation R, press the electromagnetic switch to the probe and tighten a fastening nut to 10 N. of m.
3) after installation of the electromagnetic switch, establish the lower opening of a fork of the lever of gear shifting on the center and give tension on the switch
4) the pin of the solenoid will close a fork
5) establish a gear shifting lever casing so that the lever of gear shifting was opposite to a mark N in a casing (neutral transfer);
the lever of gear shifting has to pass identical distance between provisions N and D and provisions N and R
6) install the lever A by means of a pin or a drill

In = the Pin, with a diameter of 4.0 mm, inserted into a casing opening
7) switch the gear shifting lever to situation in situation N
8) install the switch so that fastening (it is specified by an arrow) was fixed on the gear shifting lever
9) tighten fastening bolts to 5 N. of m.

10) remove a pin or a drill

After installation of the switch, check its work.