Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
- 11. Steering
11.2. Shaft and casing of a steering column
11.3. The power absorbing steering column
11.4. Steering drive
11.5. Pipeline of high pressure / return pipeline
11.6. Adjustment of a free wheeling of a lath of steering
11.7. Maple belt
+ 11.8. System of hydrostrengthening of steering
+ 12. Body, salon
+ 13. Air conditioning system
+ 14. Electric equipment
|
Steering drive
1. Steering transfer
establish precisely on the center of a shaft of a steering column
establish steering transfer so that there were no distortions and a tension
if it is necessary, move it
it is a little in places of fastening
2. Arm of cross draft
at an inhaling of nuts of fastening of cross thirst for an arm, the car has to stand on the earth
3. 45 N. of m, always replace
4. 45 N. of m, always replace
5. Washer
6. Pipelines of high pressure. Fastening inhaling moment: 50 N. of m.
establish a hose clip on
inlet hose before removal
7. 20 N. of m, always replace
8. Washer
9. Wheel casing |
10. A bolt with a head under a face key
tighten before an inhaling of bolts of fastening of steering transfer to the body panel
11. Spring washer
12. Cover
do not remove from the body panel at removal of steering transfer
establish accurately in a round flute on a casing of the main gear wheel
13. A bolt, always replace
14. Remove a connecting disk from the leading gear wheel together with a tube with flanges
15. 25 N. of m, always replace
16. Body panel
17. Return pipeline
18. Sealing rings, always replace
19. Bolt of "banjo"
inhaling moment: 40 N. of m.
before untwisting, install a hose clip on the return pipeline |
The steering drive (release models till January, 1989 of release)
1. Cover
it is possible to replace, without removing the rack steering mechanism
2. Lock ring
put on a steering lath against the stop
establish a cover on a flute,
passing on a ring circle
3. 20 N. of m.
4. Cover
5. Sealing ring *
always replace
6. Epiploon plug
is established by thicker end up
7. Toddler
the flute is turned to a cover
8. Steering lath case
if the surface of the case is damaged in an installation site of a gear washer, accurately eliminate damage before installation of an epiploon of a lath
9. Steering lath
check a lath for existence of scratches around an epiploon installation site
10. Cap
inhaling moment: 50 N. of m.
tighten by means of two center punches established at an angle in 180 ° to each other |
11. Basic ring *
always replace
is established on a cap
12. Sealing ring *, 44x2.5 mm
always replace
is established on a cap
13. Sealing ring *, 42x2 mm
14. A sealing ring *, always replace
15. Washer
16. Needle bearing
17. Washer
18. Leading gear wheel *
19. Epiploon
20. 20 N. of m.
21. Casing of the leading gear wheel
22. Ball-bearing
23. Sealing ring
always replace
24. Spring
it is inserted into the slider
25. Ring
26. Steering lath epiploon *
27. Lock ring
check correctness of installation
28. Gear washer
check correctness of installation
29. Collar
use the collar which is pulled together by means of the screw, the screw has to be turned to a body |
The system of hydrostrengthening of steering is filled with hydraulic liquid, a detail G 002 000. All elements marked with an asterisk are included in a repair kit and have to be replaced during repair.
Prevention
Moisten all epiploons in hydraulic liquid before installation. Do not try to straighten elements of steering or to carry out on them repair welding work.
Works with the drive of steering have to be carried out in a pure workplace and all elements have to contain in absolute purity.
|
|